Pengecekan Rutin Emisi Konduksi dan Radiasi Menggunakan NEXTEM SRG-RC-1006-2

Agung Yanuar Wirapraja, Ika Prawesty Wulandari

Abstract


Sebagai laboratorium pengujian, keberterimaan nilai hasil pengujian suatu sampel uji sangat penting. Selain kalibrasi dan pemeliharaan peralatan pengujian, pengecekan rutin harus dilakukan untuk mengetahui kesiapan dari peralatan pengujian. Pada satu parameter pengujian  tidak hanya melibatkan satu peralatan atau perangkat uji, namun terdiri dari beberapa peralatan pengujian yang saling berhubungan atau yang sering disebut sebagai sistem pengujian. Pengecekan rutin juga berfungsi untuk mengetahui kesiapan dari suatu sistem pengujian. Tujuan yang ingin dicapai pada penelitian ini adalah untuk mengetahui kesiapan pengujian pada parameter emisi konduksi dan radiasi berdasarkan pengecekan rutin yang dilakukan.  Pengecekan rutin pada parameter emisi konduksi dan radiasi menggunakan Comb generator Nextem SRG-RC-1006-2. Terdapat 3 (tiga) frekuensi yang akan di analisa selama pengecekan rutin dilakukan. Nilai hasil pengukuran awal akan dijadikan nilai referensi pengecekan rutin. Hasil pengukuran pengujian rutin emisi konduksi dan emisi radiasi yang dilakukan selama bulan april – juli 2017, tidak melebihi batas toleransi sebesar ± 2,5 dB jika dibandingkan dengan nilai referensi. Selisih terbesar hasil pengukuran pengecekan rutin adalah 1 dB.


As a testing laboratory, the test results acceptibility of a test sample is very important. Besides the calibration and maintenance of test equipment, routine checks shall be made to determine the readiness of the test equipment. At a test clause may involve one or more testing device, that it consists of several interconnected test equipment or integrated as a test system. Routine checking is needed to determine the readiness of a test system. The purpose of this research is to know the readiness of the test system at conducted and Radiated Emission parameters based on routine checks. Routine checking of conducted and Radiated Emission parameters are using comb generator Nextem SRG-RC-1006-2. There are 3 (three) points of frequency to be analyzed during these routine checks. The value of the initial measurement results will be the reference value of routine checks. The result of conducted and radiated routine checks during April - July 2017 does not exceed the tolerance limit of ± 2.5 dB compared to the reference value. The biggest difference between routine checks is 1 dB.


Keywords


routing checking, conducted emission, radiated emission, comb generator

Full Text:

PDF

References


P. M. Nicolae, C. M. Stoica, and G. Mihai, “Conducted Emission measurements for a laptop,” 2014 Int. Conf. Appl. Theor. Electr. ICATE 2014 - Proc., pp. 2–5, 2014.

H. W. Ott, Electromagnetic Compatibility Engineering. 2009.

J. Colotti, “EMC design fundamentals,” in 2006 IEEE Long Island Systems, Applications and Technology Conference, LISAT, 2006.

K. Armstrong, “Guide to Testing Conducted Emissions (Based on the Methods in EN 55022 and EN 55011),” In Compliance, pp. 14–27, 2011.

A. Balmori, “Electromagnetic pollution from phone masts. Effects on wildlife,” Pathophysiology, vol. 16, no. 2–3, pp. 191–199, 2009.

A. Galeev, “The effects of microwave radiation from mobile telephones on humans and animals.,” Neurosci. Behav. Physiol., vol. 30, no. 2, pp. 187–94, 2000.

S. E. Lapinsky and A. C. Easty, “Electromagnetic Interference in critical care,” J. Crit. Care, vol. 21, no. 3, pp. 267–270, 2006.

G. Mahesh, B. Subbarao, and S. Karunakaran, “Effect of power frequency harmonics in Conducted Emission measurement,” Electromagn. Interf. Compat. 2008. INCEMIC 2008. 10th Int. Conf., pp. 273–277, 2008.

N. Hapsari, “Radiasi Medan Elektromagnetik Kabel,” Fakt. Exacta, vol. 7, no. 1, pp. 12–25, 2014.

NEXTEM, “Comb Generator - EMC Product - NEXTEM Corporation,” http://www.nextem.co.jp/web/english/emcproductsj/combgeneratorj/combgeneratorj.html, 2013. [Online]. Available: http://www.nextem.co.jp/web/english/emcproductsj/combgeneratorj/combgeneratorj.html. [Accessed: 19-Oct-2017].

A. Hesener, “Electromagnetic Interference (EMI) in Power Supplies,” in Fairchild Semiconductor Power Seminar, 2011, pp. 1–16.




DOI: http://dx.doi.org/10.36048/jtpii.v2i2.3468

Refbacks

  • There are currently no refbacks.


Copyright (c) 2017 Agung Yanuar Wirapraja, Ika Prawesty Wulandari

Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.

View My Stats-->

  =====================================================

Jurnal Teknologi Proses Dan Inovasi Industri (JTPII)

Balai Riset Dan Standardisasi Industri Surabaya

Jl. Jagir Wonokromo No. 360. Surabaya. 60244

Telp. (031)8410054; Fax. (031)8410480

http://ejournal.kemenperin.go.id/jtpii

===================================================